Inland/Nippon

Inland Nippon PJ80A2-24A Unipolar Stepper Motor 1.68 Ohm/Phase 3ft Cable

(No reviews yet) Write a Review
SKU:
29556
Condition:
Used
Availability:
Currently out of stock — contact us for availability.
Weight:
5.00 LBS
Shipping:
Calculated at Checkout
  • Inland Nippon PJ80A2-24A unipolar stepper motor – left side view showing cylindrical body, square flange, and multi-color wire lead
  • Inland Nippon PJ80A2-24A stepper motor – front flange and keyed output shaft with wire lead visible
  • PJ80A2-24A stepper motor red IDC multi-pin connector close-up with 8-conductor color-coded lead
  • Inland Nippon PJ80A2-24A stepper motor – close-up of knurled 1/4-inch output shaft and square flange face
  • Inland Nippon PJ80A2-24A stepper motor label showing model PJ80A2-24A, 1.68 ohm/phase, lot 90K, part 44A501912-003, Made in Japan
$35.00

This item is temporarily unavailable. Please view our recommended, in-stock alternatives directly below.

Description

Inland Nippon PJ80A2-24A Unipolar Stepper Motor 1.68 Ohm/Phase 3ft Cable

The Inland/Nippon Pulse Motor PJ80A2-24A is a NEMA 34-class unipolar stepper motor manufactured in Japan. It features a cylindrical motor body with a square mounting flange, a knurled 1/4-inch output shaft, and an 8-conductor color-coded lead terminating in a red multi-pin IDC connector. The motor is rated at 1.68 ohms per phase and configured for unipolar drive, making it straightforward to interface with standard unipolar stepper driver circuits.

Specifications & What's Included

  • Model: PJ80A2-24A
  • Part Number: 44A501912-003
  • Manufacturer: Inland / Nippon Pulse Motor — Made in Japan
  • Winding Type: Unipolar
  • Resistance per Phase: 1.68 Ohm
  • Output Shaft Diameter: 1/4 in (knurled)
  • Shaft Length: 1.16 in
  • Flange Size: 2.22 in square
  • Mounting Hole Pattern: 0.2 in holes on a 1.87 in square bolt circle
  • Motor Body Length: 3 in
  • Motor Body Diameter: 2 in
  • Lead Wire Length: approximately 3 ft
  • Connector: Red multi-pin IDC connector, 8 conductors, color-coded wires
  • Includes: Motor with attached lead and connector — no driver board or mounting hardware

Applications

Unipolar stepper motors like the PJ80A2-24A are widely used in precision motion control applications across CNC machinery, laboratory automation, robotics, medical devices, and industrial positioning systems. The unipolar winding configuration simplifies driver design — each phase winding has a center tap, allowing simpler transistor-based drive circuits without the need for an H-bridge. The 2.22-inch square flange is consistent with NEMA 34 form factor conventions, making this motor compatible with a broad range of standard motor mounts and couplers. Nippon Pulse Motor (marketed in North America under the Inland brand) has been a respected manufacturer of precision stepping motors for industrial and OEM applications since the mid-20th century, and their motors are commonly found in legacy automation equipment, plotters, tape drive mechanisms, and scientific instrumentation.

Condition: Used
This Inland/Nippon Pulse Motor PJ80A2-24A Unipolar Stepper Motor has been inspected and appears to be in good used condition. It was pulled from a working environment where it was previously in service. The motor body shows normal handling wear consistent with used industrial equipment. The shaft, flange face, and mounting surfaces are intact with no visible damage. The 3-foot multi-conductor lead and red IDC connector appear complete and undamaged. Please view our photo set and contact us if you have any questions.
View AllClose

Warranty Information

We stand behind every item we sell with a 30-day money-back guarantee. If your item arrives not as described, you may return it within 30 days for a full refund. Please inspect your purchase upon arrival and contact us with any questions.
View AllClose

Additional Information

Brand:
Inland / Nippon Pulse Motor
Model:
PJ80A2-24A
MPN:
44A501912-003
Type:
Unipolar Stepper Motor
SKU:
29556
Resistance per Phase:
1.68 Ohm/Phase
Winding Type:
Unipolar
Shaft Diameter:
1/4 in (0.25 in)
Shaft Length:
1.16 in
Flange Size:
2.22 in square
Mounting Hole Pattern:
0.2 in holes on 1.87 in square bolt circle
Motor Body Length:
3 in
Motor Body Diameter:
2 in
Lead Wire Length:
3 ft
Connector Type:
Multi-pin red IDC connector
Number of Leads:
8
Lot Number:
90K
Country/Region of Manufacture:
Japan
Form Factor:
NEMA 34 (approx.) flange mount
Seller Notes:
Includes approx. 3ft multi-conductor lead with red IDC connector. Motor only — no driver or mounting hardware.
Condition Notes:
This Inland/Nippon PJ80A2-24A Unipolar Stepper Motor is in good used condition, pulled from a working environment. Body shows normal wear; shaft, flange, and 3ft lead with IDC connector appear intact and undamaged.
California Prop 65 Warning:
WARNING: This product can expose you to chemicals including lead and lead compounds, and DEHP (a phthalate), which are known to the State of California to cause cancer and birth defects or other reproductive harm. Go to P65Warnings.ca.gov
View AllClose